Repository navigation
EN Panda SPAS Indicator Output
Menu: Vehicle & Hardware > Indicator Control > Output Device
CanfdBlinkerKick
Sends common indicator requests through Panda using vehicle SPAS messages. Default off. Supported on camera-SCC CAN-FD with ECAN SPAS 0x165 (24 bytes), 0x16A (32 bytes) and stalk 0x3C1 (8 bytes), without a model-name restriction. Automatic indication follows Automatic turn signals, Manual Lane-change Indicator, Manual Turn Indicator and model observation settings. Start, hold and completion use the same policy as USB2CAN and BT2CAN. Auto Blinker 0 disables automatic requests and retains explicit Bluetooth indicator buttons as single taps in D. Enabling applies on the next onroad start; disabling applies immediately. Updated Panda firmware is required. Enabling suspends USB2CAN/BT2CAN output and waits for outstanding external commands and exclusive ownership. CanfdBlinkerControl is disabled on the next onroad start. Physical lever operation ends automatic output. Automatic lamp feedback is isolated from steering requests, with verified physical lever input taking priority. Ending the common request stops SPAS output and restores the ECU default session. Residual lamp flashing depends on the vehicle. Existing saved output and common indication values are retained. The former model-only flash-count setting is retired. Select indication behavior through the common settings. For manual lane changes and turns, normal completion waits for a minimum of two seconds from the first Panda/SPAS transmission request. Physical lever input, cancellation and input or lane errors end the request immediately. Actual flash count depends on the vehicle. Before a new request, requires ten CRC-valid advancing stock SPAS frames and a fresh neutral stalk. Stalk reception remains required while the ECU is temporarily silenced. Matching CAN IDs alone does not establish compatibility.
- Type: Toggle
-
Default:
0 -
Range:
0~1 - Menu: Vehicle & Hardware > Indicator Control > Output Device
Sends common indicator requests through Panda/SPAS on camera-SCC CAN-FD with verified SPAS and stalk protocols. Automatic indication, manual lane changes, manual turns and model observations follow the existing common settings, including hold and completion.
Panda/SPAS manual lane changes and turns delay normal completion until two seconds after the first transmission request. While transmission is preparing, normal completion can wait up to two seconds from observation start. Lever input, cancellation, disabling the feature, opposite lamps and input or lane errors end the request immediately. Actual flash count requires vehicle verification.
There is no model-name allowlist: USB, BLE and Panda/SPAS use the common policy when their protocol and fresh reception are verified. Matching IDs alone is insufficient; CANCEL and existing speed, lane and driver-priority conditions remain. Requires ECAN 0x165 (24 bytes), 0x16A (32 bytes) and 0x3C1 (8 bytes). Before a new request, requires ten CRC-valid advancing stock SPAS frames and a fresh neutral stalk; stalk reception remains required while the ECU is temporarily silenced.
Select Automatic turn signals and the required observation features, then restart onroad. Saved settings are retained. Automatic indication stays off at mode 0. The independent model flash-count setting is retired.
Updated Panda firmware is required. Enabling suspends USB2CAN/BT2CAN transmission and waits for outstanding commands and exclusive ownership. Verified physical lever input also ends TBT turn holds. Residual physical flashing after request completion depends on the vehicle.
문서 기준: ajouatom/openpilot의 carrot-wip 브랜치 · 내용이 현재 화면과 다르면 문서 작성 가이드를 참고해 알려주세요.
- 소개
- 처음 시작하기
- 깜빡이 제어 장치
- 사용 설명서
- CarrotAssist 음성 도우미
-
설정 이해하기
-
전체 설정
- 주행 제어
- 시작·오토
- Tesla 전용
- 버튼·프리셋
- 차량 조향
- ONNX 차선·BSD
- 중앙 보정
- 조향감
- 차로 변경 (자동 턴)
- 레인모드
- 고급 토크
- 토크 계수
- 조향 제한
- 속도·감속
- 과속카메라
- 후면단속 통과 후 유지 거리(m)
- 과속카메라감속 완료 시간(6초)
- 네비게이션감속모드(2)
- 차량 내비 CAN 감속 적용 모드
- 차량 내비 어린이보호구역 30km/h 제한
- 차량 내비 감속 중지 요청
- 감속 중지: 박스형 카메라
- 감속 중지: 이동식 단속 구간
- 감속 중지: 과속방지턱
- 감속 중지: 과속카메라 종류 미탐지 건 [실험]
- 감속 중지: 경고 조기 시작 보정 [실험]
- 차량 내비 구간단속 평균속도 제어
- 차량 수신 과속카메라 감속(항상 적용)
- 차량 과속카메라 가상거리 시간(6.0초)
- 과속카메라 감속율 x0.01m/s^2(120)
- 네비알림 카운트다운 방법
- 과속카메라 제한속도적용율(105)%
- 제한속도
- 방지턱
- 커브·턴
- 신호감지
- 과속카메라
- 크루즈·차간
- 가속 성향
- 정차·재출발
- 가감속 튜닝
- 차간거리
- 당근 크루즈
- 차량·하드웨어
- 현대·기아
- 깜박이 제어
- CANFD·HDA
- 레이더
- 운전자 모니터링
- 차량 보조
- 기기 하드웨어
- 화면 표시
- 정보 표시
- 경로 표시
- 밝기·주행화면
- 외부 HUD
- 시스템
- 녹화·전원
- 녹화·전원
- 카메라
- 네트워크·지도
- 사운드
- 소프트웨어
- 녹화·전원
- 주행 제어
- 버튼·프리셋 상세
- 속도·감속 상세
- 크루즈·차간 상세
- 레이더트랙·코너레이더
- 차로 변경 이해하기
-
전체 설정
- Carrot Web
- 튜닝 입문
- 자주 묻는 질문
- 문서 작성 가이드