Skip to content

nanovna 07 Quick Reference Card

github-actions[bot] edited this page Nov 15, 2026 · 1 revision

Reference index and audit status: Reviewed cheat sheets and references.

Note

Selected formula and usage audit: October 31, 2026. Numeric values are rounded; dynamic range, resonance, calibration and band limits depend on exact NanoVNA hardware, clones, firmware and test fixtures. Do not assume a calibration at one sweep range is valid across arbitrary spans. See the NanoVNA index and calibration procedures for required prerequisites.

Keep the common procedures, display choices, and diagnostic checks close at hand.

Part of the ULTIMATE CYBERSECURITY MASTER GUIDE ยท SDR & RF

NanoVNA Focus Chapter


โ† NanoVNA Index ยท SDR & RF

๐ŸŽฏ Purpose

Provide a compact companion to the detailed measurement chapters.

โš™๏ธ Function

Collect checklists, conversion tables, formulas, presets, and troubleshooting references.

๐Ÿ† Goal

Find the relevant operating reminder quickly during a measurement session.

๐Ÿ“‹ When to Use

  • Working at the bench or reviewing the field checklist.
  • Looking up a formula, marker operation, or display format.

๐Ÿ“‹ Table of Contents


Print this. Tape it inside the case lid.


Pre-flight (every measurement)

โ–ก Radio physically DISCONNECTED
โ–ก DC block inline (unknown systems)
โ–ก Coax center shorted to shield for 3 s
โ–ก Sweep span set
โ–ก Calibrated on THIS span
โ–ก "C" indicator visible on screen
โ–ก LOAD check: โˆ’35 dB or better

Max input: +10 dBm (community figure, no verified spec). That is 1/100 W. Any transmitter, any power, destroys the front end.


The 90-second calibration

1.  STIMULUS โ†’ START / STOP
2.  Attach test cable + adapters
3.  CAL โ†’ RESET
4.  CAL โ†’ CALIBRATE
5.  OPEN  โ†’ tap OPEN  โ†’ wait for sweep
6.  SHORT โ†’ tap SHORT โ†’ wait
7.  LOAD  โ†’ tap LOAD  โ†’ wait
8.  DONE
9.  CAL โ†’ SAVE โ†’ slot n
10. Verify with LOAD

VSWR โ†” reflection โ†” reflected power

Sign convention: the screen's S11 LOGMAG is negative (more negative = better). Return loss quoted positively is the same number flipped (larger = better). S11 LOGMAG = โˆ’(return loss). Never say "โˆ’20 dB return loss."

VSWR S11 LOGMAG Return loss Refl. power Mismatch loss
1.0 โˆ’โˆž โˆž 0% 0.00 dB
1.1 โˆ’26.4 26.4 0.2% 0.01 dB
1.2 โˆ’20.8 20.8 0.8% 0.04 dB
1.3 โˆ’17.7 17.7 1.7% 0.07 dB
1.5 โˆ’14.0 14.0 4.0% 0.18 dB
2.0 โˆ’9.5 9.5 11.1% 0.51 dB
2.5 โˆ’7.4 7.4 18.4% 0.88 dB
3.0 โˆ’6.0 6.0 25.0% 1.25 dB
5.0 โˆ’3.5 3.5 44.4% 2.55 dB
10.0 โˆ’1.7 1.7 66.9% 4.81 dB

SEARCH โ†’ MINIMUM finds the best match on SWR or LOGMAG. If your display plots positive return loss, the best match is a MAXIMUM.


Smith chart โ€” instant diagnosis

         INDUCTIVE  (+jX)  โ†’  diagnose: may be too long for simple resonant wire
       โ”Œโ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”
      โ•ฑ                      โ•ฒ
SHORTโ”‚          โ— 50ฮฉ         โ”‚OPEN
 0ฮฉ   โ•ฒ       (center)       โ•ฑ  โˆžฮฉ
       โ””โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”˜
         CAPACITIVE (โˆ’jX)  โ†’  diagnose: may be too short for simple resonant wire

  Left of center on centerline  โ†’ R < 50ฮฉ, needs step-up
  Right of center on centerline โ†’ R > 50ฮฉ, needs step-down

Key formulas

ฮ“          = (Z โˆ’ 50) / (Z + 50)
Z          = 50 ยท (1 + ฮ“) / (1 โˆ’ ฮ“)
|ฮ“|        = (SWR โˆ’ 1) / (SWR + 1)
VSWR       = (1 + |ฮ“|) / (1 โˆ’ |ฮ“|)
S11 LOGMAG =  20 ยท logโ‚โ‚€(|ฮ“|)      dB   (negative on screen)
Return loss= โˆ’20 ยท logโ‚โ‚€(|ฮ“|)      dB   (positive by convention)
Refl. power= |ฮ“|ยฒ
Mismatch loss = โˆ’10 ยท logโ‚โ‚€(1 โˆ’ |ฮ“|ยฒ)  dB

FREE SPACE                      PRACTICAL (โ‰ˆ5% end effect)
ฮป   (m) = 299.79 / f(MHz)       dipole ฮป/2 (m)  = 142.65 / f(MHz)  total
ฮป/2 (m) = 149.90 / f(MHz)       dipole ฮป/2 (ft) = 468    / f(MHz)  total
ฮป/4 (m) =  74.95 / f(MHz)       ฮป/4 element (m) =  71.3  / f(MHz)
ฮป/4 (ft)= 246    / f(MHz)       ฮป/4 element (ft)= 234    / f(MHz)
                                (radials: use the free-space figure)

Coax ฮป/4 (m)  = (75 ร— VF) / f(MHz)
Coax ฮป/2 (m)  = (150 ร— VF) / f(MHz)
VF            = (L(m) ร— fโ‚(MHz)) / 75     from first open-stub dip

Length trim: if resonant length decreases by fraction x, f_new โ‰ˆ f_old / (1 โˆ’ x)
             (so 10% shorter raises frequency โ‰ˆ11.1%, not exactly 10%).
             Make SMALL incremental trims; measure after each adjustment.

L-network:    Q  = โˆš(R_high/R_low โˆ’ 1)
              X_series = Q ร— R_low        (low-R side)
              X_shunt  = R_high / Q       (high-R side)
              L = X / (2ฯ€f)    C = 1 / (2ฯ€fยทX)

ฮป/4 transformer:  Z = โˆš(Z_source ร— Z_load)
Hairpin match condition:  |X_s| = โˆš(R_s ร— (50 โˆ’ R_s))

Ripple spacing โ†’ distance:  d(m) = (150 ร— VF) / ฮ”f(MHz)
Cable loss (shorted far end) = (return loss in dB) / 2
Sweep resolution = Span / (Points โˆ’ 1)

TDR, sweep bandwidth B and step ฮ”f, c = 299,792,458 m/s:
  resolvable separation   ฮ”d โ‰ˆ VF ร— c / (2B)
  ambiguity distance       d โ‰ˆ VF ร— c / (2ฮ”f)
  distance from round trip   = VF ร— c ร— t / 2

Velocity factors

Cable / Construction Approximate VF
RG-58 / RG-213 / RG-59 (solid polyethylene dielectric) 0.66
RG-8X (foam dielectric) 0.82
RG-174 0.66
RG-6 (foam dielectric) 0.83
RG-316 0.695
LMR-240 / LMR-400 0.84โ€“0.85
Semi-rigid PTFE 0.70
Hardline 0.88
Ladder line 0.90โ€“0.95

Band presets

ฮป/4 uses the practical constant (71.3/f). Start long.

Service Frequency ฮป/4 element Discovery sweep Detail sweep
80 m 3.75 MHz 19.01 m 3.0โ€“4.5 MHz 3.4โ€“4.1 MHz
40 m 7.15 MHz 9.972 m 6โ€“9 MHz 6.8โ€“7.5 MHz
20 m 14.2 MHz 5.021 m 12โ€“16 MHz 13.9โ€“14.5 MHz
CB 27.2 MHz 2.621 m 25โ€“30 MHz 26.5โ€“28.0 MHz
10 m 28.5 MHz 2.502 m 25โ€“32 MHz 27.5โ€“29.8 MHz
6 m 52 MHz 1.371 m 45โ€“60 MHz 50โ€“54 MHz
Airband 125 MHz 57.04 cm 100โ€“150 MHz 118โ€“137 MHz
2 m 146 MHz 48.84 cm 130โ€“170 MHz 140โ€“152 MHz
MURS 152 MHz 46.91 cm 130โ€“170 MHz 150โ€“155 MHz
Marine VHF 157 MHz 45.41 cm 130โ€“180 MHz 155โ€“163 MHz
433 ISM 433.92 MHz 16.43 cm 400โ€“470 MHz 420โ€“450 MHz
70 cm 435 MHz 16.39 cm 400โ€“470 MHz 420โ€“450 MHz
GMRS/FRS ~464.5 MHz 15.35 cm 400โ€“520 MHz 455โ€“470 MHz
868 ISM 868 MHz 8.21 cm 800โ€“950 MHz 863โ€“870 MHz
915 ISM / LoRa 915 MHz 7.79 cm 850โ€“1000 MHz 902โ€“928 MHz
ADS-B 1090 MHz 6.54 cm 1000โ€“1150 MHz 1070โ€“1110 MHz

Sweep spans are measurement suggestions, not band-allocation statements. Recalibrate after narrowing.


Troubleshooting flowchart

Sweep looks wrong
โ”‚
โ”œโ”€ No "C" indicator? โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Calibrate
โ”‚
โ”œโ”€ Flat 1.0:1 everywhere? โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Dummy load, or lossy/waterlogged coax
โ”‚                                     Check Smith: tight dot = load
โ”‚
โ”œโ”€ Pinned at max SWR everywhere? โ”€โ”€โ†’ Open or short
โ”‚     โ”œโ”€ Smith at far RIGHT โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ OPEN: broken conductor / nothing connected
โ”‚     โ””โ”€ Smith at far LEFT โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ SHORT: crushed coax / failed arrestor
โ”‚     โ””โ”€ Run TDR to locate the fault
โ”‚
โ”œโ”€ Dip at wrong frequency? โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Trim length
โ”‚     โ”œโ”€ Dip too LOW  โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Element too long โ†’ shorten
โ”‚     โ””โ”€ Dip too HIGH โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Element too short โ†’ lengthen
โ”‚
โ”œโ”€ Dip right, SWR still high? โ”€โ”€โ”€โ”€โ”€โ†’ Match problem, not length
โ”‚     โ””โ”€ Read R on Smith, build L-network
โ”‚
โ”œโ”€ SWR changes when you touch
โ”‚  the coax? โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Common-mode current โ†’ add choke, retune
โ”‚
โ”œโ”€ Broad shallow dip, never good? โ”€โ†’ Loss: wet coax, corroded connector
โ”‚
โ”œโ”€ Evenly spaced ripple? โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Mid-run discontinuity
โ”‚                                     d(m) = (150 ร— VF) / ฮ”f(MHz)
โ”‚
โ”œโ”€ Erratic / non-repeatable? โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Loose connector, dying battery,
โ”‚                                     or bad calibration โ†’ re-torque, re-cal
โ”‚
โ”œโ”€ Reads as a short on a DMM? โ”€โ”€โ”€โ”€โ”€โ†’ May be a NORMAL DC-grounded design.
โ”‚                                     Judge by RF sweep, not continuity.
โ”‚
โ””โ”€ Stuck at exactly 1.5:1? โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ”€โ†’ Is it a 75 ฮฉ antenna? That IS its correct
                                      match on a 50 ฮฉ instrument. Don't "fix" it.

Stop and diagnose before trimming ifโ€ฆ

โœ— The calibration load does not read correctly
โœ— The trace jumps when a connector is flexed
โœ— You cannot identify which dip is the intended resonance
โœ— The result changes with hand or cable position
โœ— You are measuring through unknown or lossy coax
โœ— A complex antenna has no documented adjustment method

Display format quick pick

I want toโ€ฆ Use
Report a number to a customer SWR
Tune precisely LOGMAG (more visible resolution)
Understand why it's mismatched SMITH
Find true resonance REACTANCE (zero crossing)
See what matching R I need RESISTANCE
Measure a filter CH1 LOGMAG
Match cable lengths CH1 PHASE
Find a cable fault TRANSFORM โ†’ LOW PASS IMPULSE

Marker operations

MARKER โ†’ SEARCH โ†’ MINIMUM      drop marker on the SWR/RL minimum
MARKER โ†’ SEARCH โ†’ TRACKING     marker follows the minimum live (use while tuning)
MARKER โ†’ SEARCH โ†’ MAXIMUM      peak finding (S21 filter passband)
MARKER โ†’ OPERATIONS โ†’ โ†’CENTER  recenter the sweep on the marker
MARKER โ†’ OPERATIONS โ†’ โ†’SPAN    set span from two markers
MARKER โ†’ OPERATIONS โ†’ โ†’EDELAY  auto-set electrical delay from marker
MARKER โ†’ SELECT โ†’ DELTA        show differences between markers

Dynamic range by band

Range Usable range Notes
9โ€“50 kHz Poor Noisy
50 kHz โ€“ 300 MHz ~70 dB Fundamental โ€” best performance
300โ€“900 MHz ~50 dB 3rd harmonic
900 MHz โ€“ 1.5 GHz ~40 dB 5th harmonic
Above 1.5 GHz ~25โ€“30 dB Firmware-dependent, S11 only, don't trust S21

These units do not usefully cover 2.4 GHz Wi-Fi/BLE or 5 GHz.


Things that kill the instrument

โœ— Transmitting into it (any power)
โœ— DC on the feedline
โœ— Static from an outdoor antenna
โœ— Nearby high-power transmitter coupling in
โœ— Over-torquing the SMA connectors
โœ— RP-SMA forced onto standard SMA

โ† Cables & filters | Next: PC software & firmware โ†’

More: worked examples ยท special antenna types ยท worksheet



๐Ÿ“„ Source: SDR/nanovna/07-quick-reference.md | โœ๏ธ Suggest an edit | โฌ…๏ธ Back to Software-Defined Radio

Clone this wiki locally